mktcpip Command

Purpose

Sets the required values for starting TCP/IP on a host.

Syntax

mktcpip { -S Interface | -h HostName -a Address -i Interface [ -s ] [ -m SubnetMask ] [ -r RingSpeed ] [ -t CableType ] [ -g DefaultGateway ] [ -n NameServerAddress [ -d Domain ] ] [ [ -c Subchannel ] -D Destination ] }

Description

The mktcpip command sets the required minimal values required for using TCP/IP on a host machine. These values are written to the configuration database.
Note: The mktcpip command currently supports IPv4 only.
The basic functions of the mktcpip command include:

You can use the Network application in Web-based System Manager (wsm) to change network characteristics. You could also use the System Management Interface Tool (SMIT) smit mktcpip fast path to run this command.

Flags

Item Description
-a Address Sets the Internet address of the host. Specify the address in dotted decimal notation. Each network interface on the host should have a unique Internet address. The following is the standard format for setting the Internet address:
127.10.31.2
-c Subchannel Specifies the subchannel address for a System/370 channel adapter.
-D Destination Sets the destination address for a static route. Specify the address in dotted decimal notation. The following is the standard format for setting the destination address for a static route:
192.9.52.1
-d Domain Specifies the domain name of the name server the host should use for name resolution, if any. The domain name should be in the following format:
subdomain.subdomain.rootdomain
-g DefaultGateway Adds the default gateway address to the routing table. Specify the address in dotted decimal notation. The following is the standard format for setting the default gateway address:
192.9.52.0
-h HostName Sets the name of the host. If using a domain naming system, the domain and any subdomains must be specified. The following is the standard format for setting the host name:
hostname

The following is the standard format for setting the host name in a domain naming system:

hostname.subdomain.subdomain.rootdomain
-i Interface Specifies a particular network interface, for example:
tr0
-m SubnetMask Specifies the mask the gateway should use in determining the appropriate subnetwork for routing. The subnet mask is a set of 4 bytes, as in the Internet address. The subnet mask consists of high bits (1s) corresponding to the bit positions of the network and subnetwork address, and low bits (0s) corresponding to the bit positions of the host address.
-n NameServerAddress Specifies the Internet address of the name server the host uses for name resolution, if applicable. The address should be entered in dotted decimal notation, as follows:
127.1.0.1
-r RingSpeed Specifies the ring speed for a token-ring adapter. Valid values for the RingSpeed variable are either 4- or 16-Mbps.
-S Interface Retrieves information for System Management Interface Tool (SMIT) display.
-s Starts the TCP/IP daemons.
-t CableType Specifies cable size for Standard Ethernet or IEEE 802.3 Ethernet networks. Valid values for the CableType variable are dix for thick cable, bnc for thin cable, or N/A for Not Applicable. The -t CableType flag should be used only for Standard Ethernet (en) and IEEE 802.3 Ethernet (et) interfaces.

Examples

To set the required values for starting TCP/IP enter:

mktcpip -h fred.austin.century.com -a 192.9.200.4 -i en0 \
-n 192.9.200.1 -d austin.century.com -s
Note: Use the mktcpip command only to minimally configure TCP/IP for the first time. For further configuration changes, use the smitty configtcp fastpath.

Files

Item Description
/usr/bin/mktcpip Contains the mktcpip command.
/etc/resolv.conf Contains the default system configuration database.
/etc/hosts Contains the host name and IP address entries.