eucioctl(5)


eucioctl -- generic interface to EUC handling tty drivers and modules

Synopsis

   #include <sys/eucioctl.h>
   

ioctl(int fd, I_STR, struct strioctl *sb);

Description

This interface is implemented in tty drivers and pushable STREAMS modules that handle EUC codes. It is intended as a generic interface for EUC handling, to eliminate an explosion of module-specific ioctl calls that would otherwise be necessary, and to provide uniformity in dealing with EUC code sets in the tty subsystem.

Several calls are defined. The first two calls take an argument, which is expected to be a pointer to an eucioc structure, defined in the header file sys/eucioctl.h:

   	struct eucioc {
   		unsigned char eucw[4];
   		unsigned char scrw[4];
   	};
   	typedef struct eucioc	eucioc_t;

In all cases, these calls return non-zero on failure. Failure should be usually taken as an indication that the current driver, or line discipline module, does not support EUC, in which case errno will be set to EINVAL. For the EUC_WSET or EUC_WGET calls, errno will be set to EPROTO if struct eucioc argument is invalid.


EUC_WSET
This call takes a pointer to an eucioc structure, and uses it to set the EUC line discipline's local definition for the code set widths to be used for subsequent operations. Within the stream, the line discipline may optionally notify other modules of this setting via M_CTL messages.

EUC_WGET
This call takes a pointer to an eucioc structure, and returns in it the EUC code set widths currently in use by the EUC line discipline. It needs to be recognized only by line discipline modules.

The following calls take no arguments. They should only fail if the driver (at the bottom of the tty stream) does not recognize EUC codes. Drivers that support EUC, whether the stream contains modules that respond to the calls or not, will recognize the calls and acknowledge them. These calls are normally only interpreted by modules that have modes other than ASCII, and/or do some form of I/O conversion that normally prevents a program from receiving non-EUC characters in its byte stream. All of these calls, when received by modules, are passed down the tty stream, to be ultimately acknowledged by the tty driver.


EUC_MSAVE
This call has no effect on modules that are currently in ASCII mode. Otherwise (i.e., for modules not in ASCII mode), the following actions are taken by all modules that recognize this call: (1) the current mode status is saved, (2) the mode is changed to ASCII mode immediately.

EUC_MREST
If a mode was saved via a previous EUC_MSAVE call, the saved mode is restored, and the saved state flag is cleared. If the mode was not previously saved, this call has no effect. (The exact semantics are somewhat dependent on the module, since some modules may respond to specific user requests to switch modes, even while a mode is being saved via EUC_MSAVE.)

EUC_IXLOFF
If a module is currently in a state where input conversion is being performed on the incoming byte stream, then input conversion is turned off, and the module's mode status is saved. If no input conversion is being performed, there is no effect on the module. The purpose of this call is to provide a way of insuring a pure byte stream to the program. The byte stream while input conversion is off is, of course, not guaranteed to be a stream of EUC characters. Turning off input conversion is roughly equivalent to the old concept of raw mode, if used in conjunction with ICANON off. It should normally not be used by applications.

EUC_IXLON
If a module previously saved its state and turned off input conversion, then input conversion is restored (i.e., turned back on); otherwise, there is no effect.

EUC_OXLOFF
In a manner similar to EUC_IXLOFF, any output conversion is turned off and the current mode status saved.

EUC_OXLON
In a manner similar to EUC_IXLON, any saved output conversion status is restored (i.e., output conversion is turned back on if previously turned off via EUC_OXLOFF).

Files

/usr/include/sys/eucioctl.h

Notices

Drivers and modules that support EUC should all respond appropriately to these calls, depending on their type. Line disciplines must respond to EUC_WSET and EUC_WGET, changing their current code set sizes to match EUC_WSET requests. All tty STREAMS modules that do any input or output conversion should recognize the other calls; modules that do no code set conversion are not required to recognize the calls, but must pass them through. Drivers that support EUC tty streams must all acknowledge the ON/OFF calls, whether the drivers themselves are affected or not, since these calls are purposely not acknowledged by modules which receive them; they are intended to be made available for affecting all modules in the whole stream.

Adherence to this protocol for all EUC handling modules is strongly encouraged in order to increase portability and language-independence of applications. These calls are intended as a small set of primitives to help reduce an anticipated plethora of module- and language-dependent operations.


© 2004 The SCO Group, Inc. All rights reserved.
UnixWare 7 Release 7.1.4 - 25 April 2004