select(3C)


select, FD_CLR, FD_ISSET, FD_SET, FD_ZERO -- synchronous I/O multiplexing

Synopsis

#include <sys/time.h>
#include <sys/types.h>
#include <sys/select.h>

int select(int nfds, fd_set *readfds, fd_set *writefds, fd_set *exceptfds, struct timeval *timeout);

void FD_SET(int fd, fd_set *fdset);

void FD_CLR(int fd, fd_set *fdset);

int FD_ISSET(int fd, fd_set *fdset);

void FD_ZERO(fd_set *fdset);

Description

select examines the I/O descriptor sets whose addresses are passed in readfds, writefds, and exceptfds to see if any of their descriptors are ready for reading, are ready for writing, or have an exceptional condition pending, respectively. nfds is the number of bits to be checked in each bit mask that represents a file descriptor; the descriptors from 0 to nfds-1 in the descriptor sets are examined. On return, select replaces the given descriptor sets with subsets consisting of those descriptors that are ready for the requested operation. The return value from the call to select() is the number of ready descriptors.

The descriptor sets are stored as bit fields in arrays of integers. The following macros are provided for manipulating such descriptor sets:


FD_ZERO(&fdset)
initializes a descriptor set fdset to the null set.

FD_SET(fd, &fdset)
includes a particular descriptor fd in fdset.

FD_CLR(fd, &fdset)
removes fd from fdset.

FD_ISSET(fd, &fdset)
is nonzero if fd is a member of fdset, zero otherwise.

The behavior of these macros is undefined if a descriptor value is less than zero or greater than or equal to FD_SETSIZE. FD_SETSIZE is a constant defined in sys/select.h. In UnixWare 7 and previous releases of UnixWare, its value was 1024. FD_SETSIZE was increased to 4096 in UnixWare 7 Release 7.0.1. See ``Notices''.

If timeout is not a NULL pointer, it specifies a maximum interval to wait for the selection to complete. If timeout is a NULL pointer, the select blocks indefinitely. To affect a poll, the timeout argument should be a non-NULL pointer, pointing to a zero-valued timeval structure.

Any of readfds, writefds, and exceptfds may be given as NULL pointers if no descriptors are of interest.

Return values

select returns the number of ready descriptors contained in the descriptor sets or -1 if an error occurred. If the time limit expires, then select returns 0.

Errors

An error return from select indicates:

EBADF
One of the I/O descriptor sets specified an invalid I/O descriptor.

EINTR
A signal was delivered before any of the selected events occurred, or the time limit expired.

EINVAL
A component of the pointed-to time limit is outside the acceptable range:

0 <= tv_sec < 10^8
0 <= tv_usec < 10^6


EINVAL
File descriptors must not refer to a STREAM or multiplexer linked downstream from a multiplexer.

References

poll(2), read(2), write(2)

Notices

The default value for FD_SETSIZE (currently 4096) can cause unexpected stack overflow problems in multi-threaded applications that use select. This can typically be worked around by re-defining FD_SETSIZE to a smaller value (as in cc ... -D FD_SETSIZE=1024).

In future versions of the system, select may return the time remaining from the original timeout, if any, by modifying the time value in place. It is thus unwise to assume that the timeout value will be unmodified by the select call.

The descriptor sets are always modified on return, even if the call returns as the result of a timeout.

A file descriptor for a socket that is listening for connections will, when connections are available, indicate that it is ready for reading. A file descriptor for a socket that is connecting asynchronously will, when a connection has been established, indicate that it is ready for writing.

A connection failure on a file descriptor for a socket sets exceptfds for the file descriptor.

When a socket is shut down or closed for read operations, the setting of bits in exceptfds is determined by the value of the ss_selectrdband parameter set by inconfig(1Mtcp).


© 2004 The SCO Group, Inc. All rights reserved.
UnixWare 7 Release 7.1.4 - 25 April 2004