| FSTAB(5) | File Formats Manual | FSTAB(5) |
Each configuration line/record in fstab has the format:
fs_spec fs_file fs_vfstype fs_mntops fs_freq fs_passno
The first field, (fs_spec), describes the block special device or remote file system to be mounted. For file systems of type ffs, the special file name is the block special file name, and not the character special file name. If a program needs the character special file name, the program must create it by appending a “r” after the last “/” in the special file name.
The second field, (fs_file), describes the mount point for the file system. For swap and dump partitions, this field should be specified as “none”.
The third field, (fs_vfstype), describes the type of the file system. The system currently supports these file systems:
The fourth field, (fs_mntops), describes the mount options associated with the file system. It is formatted as a comma separated list of options. It contains at least the type of mount (see fs_type below) plus any additional options appropriate to the file system type.
The option “auto” can be used in the “noauto” form to cause a file system not to be mounted automatically (with “mount -a” , or system boot time).
If the options “userquota” and/or “groupquota” are specified, the file system is automatically processed by the quotacheck(8) command, and legacy user and/or group disk quotas are enabled with quotaon(8). By default, file system quotas are maintained in files named quota.user and quota.group which are located at the root of the associated file system. These defaults may be overridden by putting an equal sign and an alternative absolute pathname following the quota option. Thus, if the user quota file for /tmp is stored in /var/quotas/tmp.user, this location can be specified as:
userquota=/var/quotas/tmp.user
It is recommended to turn on the new, in-file system quota with tunefs(8) or at newfs(8) time, and to not use the “userquota” or “groupquota” options. Migration of limits to the new in-file system quota can be handled via quotadump(8) and quotarestore(8).
The option “rump” is used to mount the file system using a rump(3) userspace server instead of the kernel server.
The type of the mount is extracted from the fs_mntops field and stored separately in the fs_type field (it is not deleted from the fs_mntops field). If fs_type is “rw” or “ro” then the file system whose name is given in the fs_file field is normally mounted read-write or read-only on the specified special file. If fs_type is “sw” or “dp” then the special file is made available as a piece of swap or dump space by the swapctl(8) command towards the beginning of the system reboot procedure. See swapctl(8) for more information on configuring swap and dump devices. The fields other than fs_spec and fs_type are unused. If fs_type is specified as “xx” the entry is ignored. This is useful to show disk partitions which are currently unused.
The fifth field, (fs_freq), is used for these file systems by the dump(8) command to determine which file systems need to be dumped. If the fifth field is not present, a value of zero is returned and dump(8) will assume that the file system does not need to be dumped.
The sixth field, (fs_passno), is used by the fsck(8) program to determine the order in which file system checks are done at reboot time. The root file system should be specified with a fs_passno of 1, and other file systems should have a fs_passno of 2. Filesystems within a drive will be checked sequentially, but file systems on different drives will be checked at the same time to use parallelism available in the hardware. If the sixth field is not present or zero, a value of zero is returned and fsck(8) will assume that the file system does not need to be checked.
#define FSTAB_RW "rw" /* read-write device */
#define FSTAB_RQ "rq" /* read/write with quotas */
#define FSTAB_RO "ro" /* read-only device */
#define FSTAB_SW "sw" /* swap device */
#define FSTAB_DP "dp" /* dump device */
#define FSTAB_XX "xx" /* ignore totally */
struct fstab {
char *fs_spec; /* block special device name */
char *fs_file; /* file system path prefix */
char *fs_vfstype; /* type of file system */
char *fs_mntops; /* comma separated mount options */
char *fs_type; /* rw, ro, sw, or xx */
int fs_freq; /* dump frequency, in days */
int fs_passno; /* pass number on parallel fsck */
};
The proper way to read records from fstab is to use the routines getfsent(3), getfsspec(3), and getfsfile(3).
| March 6, 2011 | NetBSD 6.1 |