RUM(4) Kernel Interfaces Manual RUM(4)

NAME

rumRalink Technology USB IEEE 802.11a/b/g wireless network device

SYNOPSIS

rum* at uhub? port ?

DESCRIPTION

The rum driver supports USB 2.0 wireless adapters based on the Ralink RT2501USB and RT2601USB chipsets.

The RT2501USB chipset is the second generation of 802.11a/b/g adapters from Ralink. It consists of two integrated chips, an RT2571W MAC/BBP and an RT2528 or RT5226 radio transceiver.

The RT2601USB chipset consists of two integrated chips, an RT2671 MAC/BBP and an RT2527 or RT5225 radio transceiver. This chipset uses the MIMO (multiple-input multiple-output) technology with multiple antennas to extend the operating range of the adapter and to achieve higher throughput. MIMO is the basis of the forthcoming IEEE 802.11n standard.

These are the modes the rum driver can operate in:

BSS mode
Also known as infrastructure mode, this is used when associating with an access point, through which all traffic passes. This mode is the default.
IBSS mode
Also known as IEEE ad-hoc mode or peer-to-peer mode. This is the standardized method of operating without an access point. Stations associate with a service set. However, actual connections between stations are peer-to-peer.
Host AP
In this mode the driver acts as an access point (base station) for other cards.
monitor mode
In this mode the driver is able to receive packets without associating with an access point. This disables the internal receive filter and enables the card to capture packets from networks which it wouldn't normally have access to, or to scan for access points.

rum supports software WEP. Wired Equivalent Privacy (WEP) is the de facto encryption standard for wireless networks. It can be typically configured in one of three modes: no encryption; 40-bit encryption; or 104-bit encryption. Unfortunately, due to serious weaknesses in WEP protocol it is strongly recommended that it not be used as the sole mechanism to secure wireless communication. WEP is not enabled by default.

CONFIGURATION

The rum driver can be configured at runtime with ifconfig(8) or on boot with ifconfig.if(5) using the following parameters:
bssid bssid
Set the desired BSSID.
-bssid
Unset the desired BSSID. The interface will automatically select a BSSID in this mode, which is the default.
chan n
Set the channel (radio frequency) to be used by the driver based on the given channel ID n.
-chan
Unset the desired channel to be used by the driver. The driver will automatically select a channel in this mode, which is the default.
media media
The rum driver supports the following media types:

autoselect
Enable autoselection of the media type and options.
DS1
Set 802.11b DS 1Mbps operation.
DS2
Set 802.11b DS 2Mbps operation.
DS5
Set 802.11b DS 5.5Mbps operation.
DS11
Set 802.11b DS 11Mbps operation.
OFDM6
Set 802.11a/g OFDM 6Mbps operation.
OFDM9
Set 802.11a/g OFDM 9Mbps operation.
OFDM12
Set 802.11a/g OFDM 12Mbps operation.
OFDM18
Set 802.11a/g OFDM 18Mbps operation.
OFDM24
Set 802.11a/g OFDM 24Mbps operation.
OFDM36
Set 802.11a/g OFDM 36Mbps operation.
OFDM48
Set 802.11a/g OFDM 48Mbps operation.
OFDM54
Set 802.11a/g OFDM 54Mbps operation.
mediaopt opts
The rum driver supports the following media options:

hostap
Select Host AP operation.
ibss
Select IBSS operation.
monitor
Select monitor mode.
-mediaopt opts
Disable the specified media options on the driver and return it to the default mode of operation (BSS).
mode mode
The rum driver supports the following modes:

11a
Force 802.11a operation.
11b
Force 802.11b operation.
11g
Force 802.11g operation.
nwid id
Set the network ID. The id can either be any text string up to 32 characters in length, or a series of hexadecimal digits up to 64 digits. An empty id string allows the interface to connect to any available access points. By default the rum driver uses an empty string. Note that network ID is synonymous with Extended Service Set ID (ESSID).
nwkey key
Enable WEP encryption using the specified key. The key can either be a string, a series of hexadecimal digits (preceded by ‘0x'), or a set of keys of the form “n:k1,k2,k3,k4”, where ‘n' specifies which of the keys will be used for transmitted packets, and the four keys, “k1” through “k4”, are configured as WEP keys. If a set of keys is specified, a comma (‘,') within the key must be escaped with a backslash. Note that if multiple keys are used, their order must be the same within the network. rum is capable of using both 40-bit (5 characters or 10 hexadecimal digits) or 104-bit (13 characters or 26 hexadecimal digits) keys.
-nwkey
Disable WEP encryption. This is the default mode of operation.

FILES

The following firmware file is loaded when an interface is brought up:

/libdata/firmware/rum/rum-rt2573
See firmload(9) for how to change this.

HARDWARE

The following adapters should work:

Airlink101 AWLL5025
ASUS WL-167g ver 2
Belkin F5D7050 ver 3
Belkin F5D9050 ver 3
CNet CWD-854 ver F
Conceptronic C54RU ver 2
D-Link DWL-G122 rev C1
D-Link WUA-1340
Edimax EW-7318USG
Gigabyte GN-WB01GS
Hawking HWUG1
LevelOne WNC-0301USB
Linksys WUSB54G rev C
Planex GW-USMM
Senao NUB-3701
Sitecom WL-113 ver 2
Sitecom WL-172
TP-LINK TL-WN321G

EXAMPLES

The following ifconfig.if(5) example configures rum0 to join whatever network is available on boot, using WEP key “0x1deadbeef1”, channel 11:

inet 192.168.1.1 netmask 255.255.255.0 nwkey 0x1deadbeef1 chan 11

The following ifconfig.if(5) example creates a host-based access point on boot:

inet 192.168.1.1 netmask 255.255.255.0 media autoselect \ 
	mediaopt hostap nwid my_net chan 11

Configure rum0 for WEP, using hex key “0x1deadbeef1”:

# ifconfig rum0 nwkey 0x1deadbeef1

Return rum0 to its default settings:

# ifconfig rum0 -bssid -chan media autoselect \ 
	nwid "" -nwkey

Join an existing BSS network, “my_net”:

# ifconfig rum0 192.168.1.1 netmask 0xffffff00 nwid my_net

DIAGNOSTICS

rum%d: failed loadfirmware of file %s
For some reason, the driver was unable to read the microcode file from the filesystem. The file might be missing or corrupted.
rum%d: could not load 8051 microcode
An error occurred while attempting to upload the microcode to the onboard 8051 microcontroller unit.
rum%d: device timeout
A frame dispatched to the hardware for transmission did not complete in time. The driver will reset the hardware. This should not happen.

SEE ALSO

arp(4), ifmedia(4), netintro(4), usb(4), ifconfig.if(5), hostapd(8), ifconfig(8), firmload(9)

Ralink Technology: http://www.ralinktech.com

HISTORY

The rum driver first appeared in NetBSD 4.0 and OpenBSD 4.0.

AUTHORS

The rum driver was written by Niall O'Higgins <niallo@openbsd.org> and Damien Bergamini <damien@openbsd.org>.

CAVEATS

The rum driver supports automatic control of the transmit speed in BSS mode only. Therefore the use of a rum adapter in Host AP mode is discouraged.
February 7, 2007 NetBSD 6.1