t_sndv Subroutine

Purpose

Send data or expedited data, from one or more non-contiguous buffers, on a connection.

Library

Standard library (libxti.a)

Syntax

#include <xti.h>
int t_sndv (int fd, const struct t_iovec *iov, unsigned it iovcount, int flags) 

Description

This function is used to send either normal or expedited data. The argument fd identifies the local transport endpoint over which data should be sent, iov points to an array of buffer address/buffer length pairs. t_sndv sends data contained in buffers iov[0], iov[1], through iov[iovcount-1]. iovcount contains the number of non-contiguous data buffers which is limited to T_IOV_MAX (an implementation-defined value of at least 16). If the limit is exceeded, the function fails with [TBADDATA].

The argument flags specifies any optional flags described below:

T_EXPEDITED

If set in flags, the data will be sent as expedited data and will be subject to the interpretations of the transport provider.

T_MORE

If set in flags, this indicates to the transport provider that the transport service data unit (TSDU) (or expedited transport service data unit ETSDU) is being sent through multiple t_sndv calls. Each t_sndv with the T_MORE flag set indicates that another t_sndv (or t_snd) will follow with more data for the current TSDU (or ETSDU).

 

The end of the TSDU (or ETSDU) is identified by a t_sndv call with the T_MORE flag not set. Use of T_MORE enables a user to break up large logical data units without losing the boundaries of those units at the other end of the connection. The flag implies nothing about how the data is packaged for transfer below the transport interface. If the transport provider does not support the concept of a TSDU as indicated in the info argument on return from t_open ort_getinfo, the T_MORE flag is not meaningful and will be ignored if set.

 

The sending of a zero-length fragment of a TSDU or ETSDU is only permitted where this is used to indicate the end of a TSDU or ETSDU, that is, when the T_MORE flag is not set. Some transport providers also forbid zero-length TSDUs and ETSDUs. See "Base Operating System error codes for services that require path-name resolution" for a fuller explanation.

If set in flags, requests that the provider transmit all data that it has accumulated but not sent. The request is a local action on the provider and does not affect any similarly named protocol flag (for example, the TCP PUSH flag). This effect of setting this flag is protocol-dependent, and it may be ignored entirely by transport providers which do not support the use of this feature.

By default, t_sndv operates in synchronous mode and may wait if flow control restrictions prevent the data from being accepted by the local transport provider at the time the call is made. However, if O_NONBLOCK is set (via t_open or fcntl), t_sndv executes in asynchronous mode, and will fail immediately if there are flow control restrictions. The process can arrange to be informed when the flow control restrictions are cleared via either t_look or the EM interface.

On successful completion, t_sndv returns the number of bytes accepted by the transport provider. Normally this will equal the total number of bytes to be sent, that is,

 (iov[0].iov_len + . . + iov[iovcount-1].iov_len) 

However, the interface is constrained to send at most INT_MAX bytes in a single send. When t_sndv has submitted INT_MAX (or lower constrained value, see the note above) bytes to the provider for a single call, this value is returned to the user. However, if O_NONBLOCK is set or the function is interrupted by a signal, it is possible that only part of the data has actually been accepted by the communications provider. In this case, t_sndv returns a value that is less than the value of nbytes. If t_sndv is interrupted by a signal before it could transfer data to the communications provider, it returns -1 with t_errno set to [TSYSERR] and errno set to [EINTR].

If the number of bytes of data in the iov array is zero and sending of zero octets is not supported by the underlying transport service, t_sndv returns -1 with t_errno set to [TBADDATA].

The size of each TSDU or ETSDU must not exceed the limits of the transport provider as specified by the current values in the TSDU or ETSDU fields in the info argument returned by t_getinfo.

The error [TLOOK] is returned for asynchronous events. It is required only for an incoming disconnect event but may be returned for other events.

Return Values

On successful completion, t_sndv returns the number of bytes accepted by the transport provider. Otherwise, -1 is returned on failure and t_errno is set to indicate the error.

Error Codes

On failure, t_errno is set to one of the following:

• A single send was attempted specifying a TSDU (ETSDU) or fragment TSDU (ETSDU) greater than that specified by the current values of the TSDU or ETSDU fields in the info argument.
• A send of a zero byte TSDU (ETSDU) or zero byte fragment of a TSDU (ETSDU) is not supported by the provider.
• Multiple sends were attempted resulting in a TSDU (ETSDU) larger than that specified by the current value of the TSDU or ETSDU fields in the info argument the ability of an XTI implementation to detect such an error case is implementation-dependent (see CAVEATS, below).
• iovcount is greater than T_IOV_MAX.