infocmp Command

Purpose

Manages terminfo descriptions.

Syntax

infocmp [ -d] [ -c] [ -n] [ -I] [ -L] [ -C] [ -r] [ -u] [ -s { d| i| l| c}] [ -v] [ -V] [ -1] [ -w Width] [ -A Directory] [ -B Directory] [TermName...]

Description

The infocmp command manages terminfo descriptions. You can use this command to:

• Compare a binary terminfo entry with other terminfo entries.
• Print a terminfo description from the binary file.
• Rewrite a terminfo description to take advantage of the use attribute.

The infocmp command prints the Boolean attributes first, the numeric attributes second, and the string attributes last.

Comparing Entries

Use the -d, -c, and -n flags to compare entries. The -d flag returns the differences between entries. The -c flag produces a list of the capabilities that are set and in common between two entries. The -n flag returns a list of the capabilities that neither entry has.

To compare terminfo entries, you specify two or more TermName parameters. The infocmp command compares the terminfo description of the first TermName parameter with each of the descriptions for the subsequent TermNames specified. If a capability is defined for only one of the terminal descriptions, the value returned will depend on the type of capability. For Boolean capabilities the infocmp command returns an F, the command returns a -1 for integer capabilities, and null for string capabilities.

Producing a Source Listing

Use the -l (uppercase i), -L, -C, and -r flags to produce a source listing for one or more terminals. If you do not specify a TermName parameter, the system uses the TERM environment variable. You can use these source options to produce a source file for a terminfo binary when one is not available.

The I (uppercase i) flag produces a listing with the terminfo names. The -L flag produces a listing using the long C variable names listed in /usr/include/term.h.

The -C flag uses termcap names instead of terminfo capability names when producing the source listing. The infocmp commands translates and outputs only those terminfo capabilities that have a corresponding termcap code name. To remove this restriction, specifying the -r flag. This flag causes the command to output terminfo capabilities that cannot be translated into termcap format.

When using the -C and -r flags, the infocmp command notes any string parameters it was unable to convert to the termcap format. You must edit these parameters manually. The command collects all padding information for strings together and places it at the beginning of the string where termcap expects it. Mandatory padding is optional after translation. Mandatory padding is padding information with a trailing / (slash).

Definitions with the use Attribute

Given a list of terminal menus and the -u flag, the infocmp command compares the first terminal's description against the other terminal descriptions. The infocmp command then creates a new description for the first terminal using as much of the subsequent terminal descriptions as possible.

When you specify the -u flag and a list of terminal names, the infocmp command does the following:

• Compares subsequent terminal descriptions against the first.
• Creates a description of the first terminal you specified relative to the description of the other terminals.

The new description for the first terminal will have the following:

• Capabilities that exist in the subsequent terminals but do not exist for the first terminal will appear with an @ in the resulting description.

  Note: The @ implies that the capability does not exist.

• Capabilities defined in a subsequent terminal with the same value are replaced with use=<subsequent terminal>.
• Any capabilities in the first terminal not found in any of the other terminals are printed along with the corresponding values.
• If the first terminal has a capability whose value differs from the value found in at least one of the other terminals, the capability is printed.

You can change a description and specify a capability after the use attribute. If this capability is also found in the terminal referenced by the use attribute, the second capability takes precedence over the one referenced by the use attribute.

Changing Databases

By default, terminal descriptions appear in the system terminfo database directory, /usr/share/lib/terminfo. You can specify a different database location with the TERMINFO environment variable. The infocmp command first checks to see if this variable exists. If the variable does not exist, the command uses the system terminfo database.

You can use the -A and -B flag with the infocmp command to override the system database. The -A flag identifies the terminfo database for the first TermName parameter. The -B flag identifies the database to use for any subsequent terminals you name. Together, these flags make it possible to compare descriptions for two terminals with the same name located in two different databases.

Flags

Examples

1. To list the common capabilities between the aixterm and lft terminals, enter:

   infocmp -c aixterm lft

2. To list all of the capabilities that are possible but do not currently exist for the current terminal, enter:

   infocmp -n

3. To produce a source listing for the lft terminal in terminfo format, enter:

   infocmp -I lft

4. To produce a source listing for the terminal description my_term that is located in /tmp using as much of the lft description as possible, enter:

   infocmp -A /tmp -u my_term lft

File