send(3SOCKET) Sockets Library Functions send(3SOCKET)NAME
send, sendto, sendmsg - send a message from a socket
SYNOPSIS
cc [ flag... ] file... -lsocket -lnsl [ library... ]
#include <sys/types.h>
#include <sys/socket.h>
ssize_t send(int s, const void *msg, size_t len, int flags);
ssize_t sendto(int s, const void *msg, size_t len, int flags,
const struct sockaddr *to, int tolen);
ssize_t sendmsg(int s, const struct msghdr *msg, int flags);
DESCRIPTION
The send(), sendto(), and sendmsg() functions are used to transmit a
message to another transport end-point. The send() function can be used
only when the socket is in a connected state. See connect(3SOCKET). The
sendto() and sendmsg() functions can be used at any time. The s socket
is created with socket(3SOCKET).
The address of the target is supplied by to with a tolen parameter used
to specify the size. The length of the message is supplied by the len
parameter. For socket types such as SOCK_DGRAM and SOCK_RAW that
require atomic messages, the error EMSGSIZE is returned and the message
is not transmitted when it is too long to pass atomically through the
underlying protocol. The same restrictions do not apply to SOCK_STREAM
sockets.
A return value −1 indicates locally detected errors. It does not imply
a delivery failure.
If the socket does not have enough buffer space available to hold a
message, the send() function blocks the message, unless the socket has
been placed in non-blocking I/O mode (see fcntl(2)). The select(3C) or
poll(2) call can be used to determine when it is possible to send more
data.
The flags parameter is formed from the bitwise OR of zero or more of
the following:
MSG_OOB Send out-of-band data on sockets that support this
notion. The underlying protocol must also support out-
of-band data. Only SOCK_STREAM sockets created in the
AF_INET or the AF_INET6 address family support out-of-
band data.
MSG_DONTROUTE The SO_DONTROUTE option is turned on for the duration
of the operation. It is used only by diagnostic or
routing programs.
See recv(3SOCKET) for a description of the msghdr structure.
RETURN VALUES
Upon successful completion, these functions return the number of bytes
sent. Otherwise, they return -1 and set errno to indicate the error.
ERRORS
The send(), sendto(), and sendmsg() functions return errors under the
following conditions:
EBADF s is not a valid file descriptor.
EINTR The operation was interrupted by delivery of a signal
before any data could be buffered to be sent.
EMSGSIZE The message is too large to be sent all at once (as the
socket requires), or the msg_iovlen member of the
msghdr structure pointed to by message is less than or
equal to 0 or is greater than {IOV_MAX}.
ENOMEM Insufficient memory is available to complete the opera‐
tion.
ENOSR Insufficient STREAMS resources are available for the
operation to complete.
ENOTSOCK s is not a socket.
EWOULDBLOCK The socket is marked non-blocking and the requested
operation would block. EWOULDBLOCK is also returned
when sufficient memory is not immediately available to
allocate a suitable buffer. In such a case, the opera‐
tion can be retried later.
ECONNREFUSED The requested connection was refused by the peer. For
conected IPv4 and IPv6 datagram sockets, this indicates
that the system received an ICMP Destination Port
Unreachable message from the peer in response to some
prior transmission.
The send() and sendto() functions return errors under the following
conditions:
EINVAL The len argument overflows a ssize_t.
Inconsistent port attributes for system call.
The sendto() function returns errors under the following conditions:
EINVAL The value specified for the tolen parameter is not the size
of a valid address for the specified address family.
EISCON A destination address was specified and the socket is already
connected.
The sendmsg() function returns errors under the following conditions:
EINVAL The msg_iovlen member of the msghdr structure pointed to by
msg is less than or equal to 0, or the sum of the iov_len
values in the msg_iov array overflows a ssize_t.
One of the iov_len values in the msg_iov array member of the
msghdr structure pointed to by msg is negative, or the sum of
the iov_len values in the msg_iov array overflows a ssize_t.
msg_iov contents are inconsistent with port attributes.
The send() function returns errors under the following conditions:
EPIPE The socket is shut down for writing, or the socket is connec‐
tion-mode and is no longer connected. In the latter case, if
the socket is of type SOCK_STREAM, the SIGPIPE signal is gen‐
erated to the calling thread.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Interface Stability │Committed │
├─────────────────────────────┼─────────────────────────────┤
│MT-Level │Safe │
└─────────────────────────────┴─────────────────────────────┘
SEE ALSOfcntl(2), poll(2), write(2), connect(3SOCKET), getsockopt(3SOCKET),
recv(3SOCKET), select(3C), socket(3SOCKET), socket.h(3HEAD),
attributes(5)SunOS 5.11 31 Aug 2009 send(3SOCKET)
